Super-micro-computer 5010E Manual do Utilizador Página 115
- Página / 128
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
B-1
Appendix B: AMIBIOS POST Checkpoint Codes
Appendix B
AMIBIOS POST Checkpoint Codes
When AMIBIOS performs the Power On Self Test, it writes diagnostic codes
checkpoint codes to I/O port 0080h. If the computer cannot complete the boot
process, diagnostic equipment can be attached to the computer to read I/O port
0080h.
B-1 Uncompressed Initialization Codes
The uncompressed initialization checkpoint codes are listed in
order of execution:
Checkpoint Code Description
D0h The NMI is disabled. Power on delay is starting. Next, the
initialization code checksum will be verified.
D1h Initializing the DMA controller, performing the keyboard controller
BAT test, starting memory refresh, and entering 4 GB flat mode
next.
D3h Starting memory sizing next.
D4h Returning to real mode. Executing any OEM patches and setting
the Stack next.
D5h Passing control to the uncompressed code in shadow RAM at
E000:0000h. The initialization code is copied to segment 0 and
control will be transferred to segment 0.
D6h Control is in segment 0. Next, checking if <Ctrl> <Home> was
pressed and verifying the system BIOS checksum. If either <Ctrl>
<Home> was pressed or the system BIOS checksum is bad, next
will go to checkpoint code E0h.
Otherwise, going to checkpoint code D7h.
- SUPER 1
- About This Manual 3
- Manual Organization 3
- Manual Or 5
- Chapter 3: System Interface 6
- Chapter 4: System Safety 7
- Chapter 7: BIOS 8
- Appendices: 9
- Chapter 1 11
- System Power 12
- SCSI Subsystem (5010H only) 12
- Control Panel 12
- Cooling System 13
- Figure 1-1. Rear I/O Panel 13
- Rear I/O Panel 13
- Chipset Overview 14
- Processors 15
- Onboard SCSI (5010H only) 15
- PCI Expansion Slots 15
- Onboard Controllers/Ports 16
- Other Features 16
- Headquarters 17
- European Office 17
- Asia-Pacific 17
- Chapter 2 19
- Server Installation 19
- Choosing a Setup Location: 20
- Rack Precautions: 20
- Server Precautions: 20
- Installing the Chassis Rails: 22
- Installing the Rack Rails: 22
- (with SCSI Installed) 26
- (with IDE Installed) 27
- Chapter 3 31
- System Interface 31
- 3-3 Control Panel LEDs 32
- 3-5 Power Supply Switch 33
- 3-6 Motherboard LEDs 33
- Chapter 4 35
- System Safety 35
- 4-3 ESD Precautions 37
- Tools Required 39
- Precautions 39
- Unpacking 40
- Connecting Data Cables 41
- Connecting Power Cables 41
- Connecting the Control Panel 42
- 5-5 Installing Processors 43
- 5-4 I/O Ports 43
- 5-6 Installing Memory 45
- 5-7 Adding PCI Cards 46
- 370SSR+ Motherboard 47
- 370SSE+ Motherboard 47
- SUPER 370SSR+ 48
- SUPER 370SSE+ 50
- 5-8 Connector Definitions 52
- NIC1 LED 53
- NIC2 LED 53
- Power LED 53
- Overheat LED (JOH) 54
- Serial Ports 55
- Fan Headers* 55
- Universal Serial Bus (USB) 55
- ATX PS/2 Keyboard and 56
- PS/2 Mouse Ports 56
- LAN1/LAN2 Ports 56
- Wake-On-Ring 57
- Wake-On-LAN 57
- Connector 58
- CMOS Clear 59
- Speaker Enable/Disable 59
- Onboard LAN Enable/ 59
- IDE Connectors 61
- Floppy Connector 61
- Ultra160 SCSI 62
- Connectors 62
- 6-2 Control Panel 64
- System Fan Failure 65
- Replacing System Cooling Fans 65
- Accessing the Drive Bays 66
- Power Supply Failure 70
- Replacing the Power Supply 70
- Chapter 4 73
- 7-2 BIOS Features 74
- 7-3 Running Setup 74
- The Main BIOS Setup Menu 75
- 7-4 Advanced Chipset Setup 76
- Super IO Configuration 78
- IDE Configuration 80
- Floppy Configuration 83
- Boot Settings Configuration 84
- Event Log Configuration 87
- GMCH Configuration 88
- ICH2 Configuration 92
- The settings for 94
- 7-6 PCI PnP Setup 96
- 7-7 Power Setup 100
- Boot Device Priority 106
- Hard Disk Drives 107
- Removeable Devices 107
- ATAPI CDROM Drives 107
- Supervisor Password 108
- User Password 108
- Change User Password 109
- Clear User Password 109
- Boot Sector Virus Protection 109
- Change Supervisor Password 109
- Exit Saving Changes 110
- Exit Discarding Changes 110
- Load Optimal Defaults 111
- Load Failsafe Defaults 111
- Discard Changes 111
- Notes 112
- Appendix A 113
- AMI BIOS Error Beep Codes 114
- Appendix B 115
- AMIBIOS POST Checkpoint Codes 115
- B-2 Bootblock Recovery Codes 116
- <DEL> 118
- Hit <DEL> 118
- <WAIT...> 119
- B-4 Bus Checkpoint Codes 123
- UPERSERVER 5010H/5010E Manual 124
- Appendix C 125
- List of Figures 125
- Appendix D 127
- System Specifications 127
Manuais e produtos relacionados com Hardware Super-micro-computer 5010E
Hardware Super-micro-computer X8STE Manual do Utilizador
(103 páginas)
(103 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.139 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais