Super-micro-computer X6DHi-G2 Manual do Utilizador Página 57
- Página / 120
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Chapter 4: BIOS
4-1
Chapter 4
BIOS
4-1 Introduction
This chapter describes the Phoenix BIOS™ Setup utility for the X6DH3-G2/X6DHi-
G2. The Phoenix ROM BIOS is stored in a fl ash chip and can be easily upgraded
using a fl oppy disk-based program.
Note: Due to periodic changes to the BIOS, some settings may have been added or
deleted and might not yet be recorded in this manual. Please refer to the Manual
Download area of the Supermicro web site <http://www.supermicro.com> for any
changes to the BIOS that may not be refl ected in this manual.
System BIOS
The BIOS is the Basic Input Output System used in all IBM
®
PC, XT™, AT
®
, and
PS/2
®
compatible computers. The Phoenix BIOS fl ash chip stores the system
parameters, types of disk drives, video displays, etc. in the CMOS. The CMOS
memory requires very little electrical power. When the computer is turned off, a
backup battery provides power to the BIOS fl ash chip, enabling it to retain system
parameters. Each time the computer is powered on, the computer is confi gured
with the values stored in the BIOS ROM by the system BIOS, which gains control
at boot-up.
How To Change the Confi guration Data
The CMOS information that determines the system parameters may be changed by
entering the BIOS Setup utility. This Setup utility can be accessed by pressing the
<Delete> key at the appropriate time during system boot. See below.
Starting the Setup Utility
Normally, the only visible POST (Power On Self Test) routine is the memory test. As
the memory is being tested, press the <Delete> key to enter the main menu of the
BIOS Setup utility. From the main menu, you can access the other setup screens,
such as the Security and Power menus. Beginning with Section 4-3, detailed de-
scriptions are given for each parameter setting in the Setup utility.
Warning: Do not shut down or reset the system while updating the BIOS
to prevent possible boot failure.
- SUPER 1
- Preface 3
- Table of Contents 4
- Chapter 3: Troubleshooting 5
- Chapter 4: BIOS 6
- Appendices: 6
- Chapter 1 7
- Introduction 7
- Contacting Super Micro 8
- Chapter 1: Introduction 9
- UPER X6DH3-G2 10
- Connector Description 11
- Motherboard Features 12
- 14
- 1-2 Chipset Overview 15
- 1-3 Special Features 16
- 1-4 PC Health Monitoring 16
- 1-5 ACPI Features 17
- 1-6 Power Supply 18
- 1-7 Super I/O 18
- Chapter 2 21
- Installation 21
- To Un-install the Heatsink 24
- (installed) 25
- 2-3 Installing DIMMs 26
- http:www 26
- DDR 2 Slot 27
- Release Tab 27
- Front Control Panel 28
- 2-5 Connecting Cables 29
- Serial Ports 34
- Chassis Intrusion 34
- Universal Serial Bus (USB) 35
- ATX PS/2 Keyboard and 36
- PS/2 Mouse Ports 36
- GLAN (Giga-bit Ethernet 36
- Power LED/Speaker 37
- Fan Headers 37
- Wake-On-Ring 38
- Wake-On-LAN 38
- Power SMB (I 39
- C) Connector 39
- Overheat LED (JOH) 41
- Power Supply Failure LED 41
- 2-6 Jumper Settings 42
- Watch Dog Enable 43
- CMOS Clear 43
- VGA Enable/Disable 44
- Alarm Reset (JAR) 44
- 3rd PWR Supply PWR Fault 45
- Detect (J3P) 45
- SAS Controller Enable (*For 45
- Power Force On Enable/ 46
- 2-7 Onboard Indicators 47
- Adaptec SAS Activity LED 48
- Indicators (For the X6DH3 48
- Parallel 49
- Floppy Connector 50
- IDE Connectors 51
- Chapter 3 53
- Troubleshooting 53
- Memory Errors 54
- Chapter 4 57
- 4-2 Running Setup 58
- 4-3 Main BIOS Setupʳ 58
- Main BIOS Setup Menu 59
- Multi-Sector Transfer 61
- LBA Mode Control 61
- 32 Bit I/O 61
- 4-4 Advanced Setup 62
- Processor Power Management 69
- Hardware Monitor Logic 73
- CPU Temperature Threshold 73
- 4-5 Security 74
- Set User Password 75
- Fixed Disk Boot Sector 75
- Password on Boot 75
- 4-6 Boot 76
- 4-7 Exit 77
- Appendix A 79
- BIOS POST Messages 79
- Appendix B 85
- BIOS POST Codes 85
- POST Code Description 86
- Appendix C 91
- The Enhanced Mode: 92
- The Combined Mode: 92
- RAID 1 Init 99
- Initializing Disk Drives 102
- Rebuilding Arrays 105
- Managing Arrays 107
- Deleting Arrays 108
- *Warning 108
- Creating Arrays 108
- Assigning Array Properties 109
- Adding a Bootable Array 110
- Using the Disk Utilities 115
- Operating System 117
- ATA RAID Controller Driver 118
- Supero Doctor III 119
Manuais e produtos relacionados com Hardware Super-micro-computer X6DHi-G2
Hardware Super-micro-computer X8SIL Manual do Utilizador
(101 páginas)
(101 páginas)
Hardware Super-micro-computer P4SCT Manual do Utilizador
(100 páginas)
(100 páginas)
Hardware Super-micro-computer 5010E Manual do Utilizador
(128 páginas)
(128 páginas)
Digi-star EZ3400VL manuels
Manuels d'utilisation et guides de l'utilisateur pour Équipement Digi-star EZ3400VL.
Nous fournissons des manuels en pdf 5 Digi-star EZ3400VL à télécharger gratuitement par type de document : Manuel de l'utilisateur
Comentários a estes Manuais